Setech ST-EG100-E Guide de l'utilisateur

Copyright © 2013 SETECH Security & Automation ST-EG100-E Ethernet Gateway Installation and User Guide

ST-EG100-E Installation and User Guide Installation NOTE: The baud rate of the Control's serial port must be set to 115,200, which is the factory

ST-EG100-E Installation and User Guide Configuration Chapter 3 Configuration 3.1. Background The ST-EG100-E requires the M1 Family of controls firmw

ST-EG100-E Installation and User Guide Configuration If no device is listed, activate the Search button to repeat search process. If a device is still

ST-EG100-E Installation and User Guide Configuration If successful, the system displays at the lower right corner of the ElkRP2 window. ElkRP2 is n

ST-EG100-E Installation and User Guide Configuration between 1024 and 49151, with the recommended (default) being 2101. For security reasons, this por

ST-EG100-E Installation and User Guide Configuration Figure 6 - Reboot Required Confirmation Dialog Box 17. Activate OK button and the system display

ST-EG100-E Installation and User Guide Configuration 3.4. Optional Configuration Using ElkRP2 3.4.1. Setup of User Names & Passwords If you will

ST-EG100-E Installation and User Guide Configuration each email address is 48 characters and each corresponding Message may be up to 255 characters.

ST-EG100-E Installation and User Guide Configuration Keyword Alternate Keyword Description {EMAIL_ALSO=recipients} {EA=recipients} Add comma separa

ST-EG100-E Installation and User Guide Configuration Message Example The following is an example of a complex email message set up in the ElkRP2, M1XE

ST-EG100-E Installation and User Guide Front Matter 1470 Enterprise Parkway Twinsburg, Ohio 44087 USA Phone: 330.940.1469 www.setechautomation.com e

ST-EG100-E Installation and User Guide Configuration Resulting Email Email Header: From: [email protected] To: [email protected]; [email protected] Subject:

ST-EG100-E Installation and User Guide Configuration • ChangeIP www.changeip.com Any DDNS provider that adheres to the standard protocol used by thes

ST-EG100-E Installation and User Guide Configuration an abuse of their service to force an update too often, but they will allow forced updates every

ST-EG100-E Installation and User Guide Configuration • The filter criteria consists of zone references by zone numbers and/or zone status values by n

ST-EG100-E Installation and User Guide Configuration SETECH Security & Automation Revision 1 96-300001 Page 24 of 44 The table below lists the

ST-EG100-E Installation and User Guide Virtual Keypad Chapter 4 Virtual Keypad 4.1. Virtual Keypad Access To access the Virtual Keypad Locally (on t

ST-EG100-E Installation and User Guide Virtual Keypad Figure 9 - User Code Entry The only valid characters are the number 0 through 9. All other entr

ST-EG100-E Installation and User Guide Virtual Keypad Area Menu - Presents a list of defined areas. Displayed status and all security related functi

ST-EG100-E Installation and User Guide Virtual Keypad • Bypass - Opens a dialog to allow the user to bypass a zone. Zones may only be bypassed when

ST-EG100-E Installation and User Guide Virtual Keypad • More... - Allows the user to scroll messages displayed on the first line of the alpha-numeric

ST-EG100-E Installation and User Guide Front Matter SETECH Security & Automation Revision 1 96-300001 Page 3 of 44 Table of Contents CHAPTER 1

ST-EG100-E Installation and User Guide Virtual Keypad • ON/OFF Status Button - Shows the current state (on = green, off = grey) of the associated li

ST-EG100-E Installation and User Guide Virtual Keypad The valid modes for the thermostat operation are thermostat dependent, however, typically, they

ST-EG100-E Installation and User Guide Virtual Keypad ¾ Auto - Maintains the ambient temperature between the heating and cooling setpoints. ¾ Emerge

ST-EG100-E Installation and User Guide Virtual Keypad Shows the reported temperature of available temperature probes. A value of -- indicates the zone

ST-EG100-E Installation and User Guide Virtual Keypad Displays a list of system defined macros. Macros are defined using the ELK configuration tool a

ST-EG100-E Installation and User Guide Virtual Keypad • Status Button - Shows the current state (on = green, off = grey) of the selected output. If

ST-EG100-E Installation and User Guide Virtual Keypad 4.4.6. Tools Page 4.4.6.1. Email The Email page is used to expand the email recipient list fou

ST-EG100-E Installation and User Guide Virtual Keypad • Delete - Opens the “Confirm Delete” dialog window for the currently selected entry. • Edit

ST-EG100-E Installation and User Guide Virtual Keypad 4.4.6.2. Log Displays the contents of the ELKM1 event log. • ID - Index into the system log

ST-EG100-E Installation and User Guide Virtual Keypad 4.4.6.3. License Allows the user to enter a license key. By default, if no license key has b

ST-EG100-E Installation and User Guide Introduction Chapter 1 Introduction 1.1. Description The SETECH™ ST-EG100-E™ advanced Ethernet Gateway provid

ST-EG100-E Installation and User Guide Maintenance & Troubleshooting Chapter 5 Maintenance & Troubleshooting 5.1. Firmware Installation If y

ST-EG100-E Installation and User Guide Maintenance & Troubleshooting Figure 11 - SETECH Updater Discovery Window 6. Left-click to highlight the

ST-EG100-E Installation and User Guide Maintenance & Troubleshooting 10. Activate Exit button to close the SETECH Updater window. 5.2. Troublesh

ST-EG100-E Installation and User Guide Maintenance & Troubleshooting Symptom Cause Resolution Using ElkRP2, click on M1XEP setup, then click &quo

ST-EG100-E Installation and User Guide Maintenance & Troubleshooting SETECH Security & Automation Revision 1 96-300001 Page 44 of 44 Symp

ST-EG100-E Installation and User Guide Introduction • Diagnostic Logs available via email • Omnistat2™ Humidity and Outside Temp. support • 256 bit

ST-EG100-E Installation and User Guide Introduction 1.5. Conventions The following conventions are used throughout this document: ! WARNING Informati

ST-EG100-E Installation and User Guide Introduction Router- A communications device between networks that determines the best path between them for op

ST-EG100-E Installation and User Guide Introduction SETECH Security & Automation Revision 1 96-300001 Page 8 of 44 are assigned a unique URL.

ST-EG100-E Installation and User Guide Installation Chapter 2 Installation 2.1. Installing ST-EG100-E Ethernet Gateway 1. Remove power from the M1