Setech ST-EG100-E Spécifications

DRIFTERManualPlease read the Installation section of thismanual before installing the product.

Home Button The Home button is used• in entering setup modes• in changing settings• to turn on the back-lightIts usage is described in the relevant se

5. To exit the Clock Setting mode, do not press any button for at least 15 seconds. When the display returns to its normal appearance, it means setup

ParameterNumberDescription DefaultValueRange1 Enables tank sensor 1. 1 0 – 1 2 Enables tank sensor 2. 1 0 – 1 3 Enables tank sensor 3 0 0 – 1 4 Enable

accuracy of the predicted time remaining readout . This can either be in °C or °Fdepending on parameter 5.New Battery InstallationThe Drifter unit is

dropping to zero and there being no power to lights etc.If using a power supply without a low voltage cutout, you must monitor the battery voltage a

connector, indicating the location of pin 1.Installing the DrifterPersonnelInstallation is to be carried out only by suitably qualified personnel.Inst

16Figure 1: Mounting Bracket Details80 mm42 mm47 mm5.2 mm1.8 mmMAXScrew head clearance for mounting screwsFigure 2: Fitting Drifter onto mounting brac

Battery Shunt WiringImportant: To keep track of the battery capacity, this product needs to able to measure ALL current into and out of the battery. T

18Figure 4: Battery Shunt WiringBatteryBrown, Black and Grey wires to LoadSide of ShuntYellowWire to Batteryside of ShuntWiringLoom AShunt(mount in su

Water Tank Level Wiring(a) Empty the water from the tank(s)(b) Choose a suitable side of the tank where the level-sensing bungs can be located.(c) Dri

Copyright © Setec 2014DisclaimerSetec makes no claim as to the accuracy or suitability of the information contained in this manual. Setec accepts no l

20Figure 5: Tank PreparationDrill Holes:Ensure Water Tank is empty before proceeding.Drill four (4) Ø10mm holes in Water Tank.The bottom bung is to be

21Figure 6: Fitting water-level bungsWater TankNextInsert Bung into10mm hole in tankTighten Screwon Bung to seal to tankApply a waterproof sealant to

22Figure 7: Tank, pump, and remote switch connection for ST-III Series Power SuppliesON/OFFINPUTSETEC ST-III SeriesPower SupplyOptional Accessory(Remo

Figure 8: Tank and pump connection (for NON SETEC ST-III Power Supply based Installation)23Water PumpYellowRed Water Tank 3 Water Tank 2

24Figure 9: Tank Sensor WiringWiring:When connecting tank bung wires to the connector, either crimp to wires supplied in connector or remove them and

ServicingThere are no internal user serviceable parts.SpecificationsInput Voltage: 8 – 15 VdcBattery Drain: < 3 mA (backlight off, no USB-attached

Warranty Terms and ConditionsRegistering your BM PRO product is an important step to ensure that you receive all of the benefits you are entitled to.

Notes27

025207 Rev 2ADESIGNED AND MANUFACTURED IN AUSTRALIA

ContentsIntroduction... 4Safety Precautions..

IntroductionSafety PrecautionsPlease read the Safety Precautions carefully before installing the power supply. Be sure to observe all precautions with

AccessoriesThe following accessories are provided with the retail pack for this product.Other Required Items• Two sets of cable for connecting between

About the DrifterDesigned specifically for caravan applications, the Drifter is a display unit that monitors water tank levels and the 12 V battery ch

Names and Functions of Parts Clock displayCurrent time in 12 hour mode Battery charge state Battery time remainingwhile discharging at current dischar

OperationIn normal power-on mode the unit displays the Home screen. The various display elements of the Home screen are described below.Description of

If a tank is not installed that tank indicator will always show empty (no level segments will be shown).When full, all level segments are shown.When e